What is a heat pump cylinder, and is it a thermal store?

  • Heat Pumps
  • 3 min read
  • Updated 21st November, 2026
answer

A heat pump cylinder is an unvented hot water cylinder built around a much larger coil, so it can heat water well from the lower flow temperatures a heat pump produces. It is not a thermal store, because thermal stores run hotter than a heat pump can usually supply. Advance heat pump cylinders use low resistance DN32 coils, positioned to give the low return temperatures that heat pumps need.

Why a heat pump needs its own cylinder

A heat pump supplies water at a lower temperature than a gas or oil boiler, so the coil that carries that water through the cylinder has to be much larger to pass the heat across. Advance Appliances says the coil's capacity, position and resistance matter as much as its size.

A 2013 laboratory study for the Department of Energy and Climate Change found that fast recovery coils of 2 to 3 square metres shorten reheat times, compared with 0.6 to 1 square metre in standard cylinders. Advance's heat pump coils are 2 square metres on the 150 litre model and 3 square metres on every size from 200 litres up.

What is in an Advance heat pump cylinder

  • A duplex stainless steel cylinder that stores hot water at mains pressure, working at 3 bar.
  • A DN32 low resistance coil, placed in the cylinder to give the low return temperatures heat pumps need.
  • 3kW immersion heaters: one on the ECO HPL 150, and two on the 200, 250 and 300 litre models, so one can run from solar PV.
  • A factory fitted temperature and pressure relief valve and a G3 safety kit.

The ECO range (150 to 300 litres) is A rated for heat loss, has offset primary connections and is fully recyclable. The light commercial models come in 400 and 500 litres. All are guaranteed for 25 years.

Thermal stores run hotter than a heat pump supplies

A thermal store keeps central heating water at around 75°C and heats mains water as it passes through a coil. Advance's own FAQ explains that its thermal stores work at higher temperatures than a heat pump can usually supply, which is why its heat pump cylinders are unvented instead. A heat pump can feed the Advance multi fuel thermal store only when a boiler tops the store up to 75°C. For the wider comparison, see thermal store or unvented cylinder.

Installing an unvented cylinder

Because it holds water under pressure, a heat pump cylinder falls under Part G3 of the Building Regulations; see Approved Document G on GOV.UK. The Advance installation guide says every installation must be notified to Building Control, directly or through a Competent Persons Scheme, and the installer must complete the commissioning checklist.

Advance suggests a mains supply of at least 1.5 bar and 20 litres a minute. Below that the cylinder still works, but two outlets cannot run at the same time. The cylinder fits a standard airing cupboard on any floor and must stay accessible for maintenance.

Who uses them

Paul Barlow of Bromford Housing Association told Advance: "We now have more than 100 Advance heat Pump cylinders installed across multiple Local Authority sites. The units work as expected and we have not logged any tenant issues." Read more on the housing association page, or see the full heat pump cylinder range.

key takeaways
  • A heat pump cylinder is an unvented, mains pressure cylinder with a large coil built for a heat pump's lower flow temperatures.
  • Advance coils are DN32 low resistance, 2 square metres on the 150 litre model and 3 square metres from 200 litres.
  • It is not a thermal store, because Advance thermal stores run hotter than a heat pump usually supplies.
  • As an unvented cylinder it comes under Building Regulations Part G3 and must be notified to Building Control.
  • Advance heat pump cylinders run from 150 to 500 litres, with a 25 year guarantee.

Reviewed by Geoff Egginton

Managing Director, Advance Appliances. 20+ Years experience